How it works
- Enter the patio size. Length and width in feet.
- Enter the paver from the label. Length, width and thickness in inches. Brick pavers, square pavers, anything rectangular.
- Set the base and the edge. Gravel depth in inches (4 by default for well-drained ground), straight or curved edge, and the coverage per bag from your polymeric sand label.
- Get the shopping list. Pavers, gravel and sand in cubic yards, polymeric sand bags, edging in feet and the dig depth. Print it or download a CSV.
Where the numbers come from
| Number | Value used | Source |
|---|---|---|
| Gravel base depth | 4 in to start; 4 to 6 in for walks | Interlocking Concrete Pavement Institute |
| Bedding sand depth | 1 in to start; 1 to 1.5 in | Interlocking Concrete Pavement Institute |
| Waste, straight edges | 5% | Rogue Engineer, a rule of thumb, not a standard |
| Waste, curved edges | 10% | Rogue Engineer, a rule of thumb, not a standard |
| Base gravel weight | 2,632.5 lb per cu yd | Los Angeles County Public Works, Environmental Programs (dry stone or gravel) |
| Polymeric sand coverage | From your bag | Brands differ too much for one number |
| Paver sizes | Common retail sizes | Paver sizes and thicknesses on this list are common retail sizes, many of them nominal. Use the size and thickness on your product sheet. |
ICPI counts edge restraints as part of the paving system, so edging is measured along the perimeter. Leave out a side that runs against the house or a wall. Dig depth is the base, plus the bedding sand, plus the paver thickness.
- Application Guide for Interlocking Concrete Pavements (Tech Spec 10, rev. June 2004), Interlocking Concrete Pavement Institute. Aggregate base for walks 4-6 in; bedding sand screeded 1-1.5 in; base compacted in lifts of 6 in or less; edge restraints are part of the system. This is a copy of the bulletin hosted by The Home Depot; icpi.org now redirects to masonryandhardscapes.org.
- Paver Patio Calculator (published assumptions), Rogue Engineer. Source of the 5% waste (straight edges) and 10% waste (curved edges) rule of thumb. Not an industry standard.
- Volume-to-weight conversion table (Attachment 3), Los Angeles County Public Works, Environmental Programs. Soil dry 2,025 lb and wet 2,106 lb per cu yd; stone or gravel 2,632.5 lb per cu yd; 1 ton = 2,000 lb.
How it compares
| Home and Garden America (this page) | Rogue Engineer | |
|---|---|---|
| Account needed | No | No |
| Shopping list | Printable table and CSV | "Item / Spec / Amount" table on the page |
| Print or download | Yes | Not offered; you can email the spec to yourself |
| Base, sand, polymeric sand, edging | Yes | Yes, plus a cross-section drawing |
| Default gravel base | 4 inches (change it for clay or wet ground) | 6 inches |
| Polymeric sand coverage | Taken from your bag label | Built-in 80 to 100 sq ft per bag |
| Ads and promotions | None | Sale banner, patio plans for $10 to $15 |
| Assumptions | Shown on screen | Listed in detail |
Checked in November 2026. Rogue Engineer is a solid calculator and spells out its assumptions well. The difference here is the printable list, the label-based polymeric sand and no sales pitch.
On paper
Print the shopping list and hand it to the yard at the supply store: paver count, gravel and sand in cubic yards, polymeric sand bags, edging and dig depth on one page. The CSV opens in any spreadsheet if you want to add prices.
How to plan a paver patio, from the dirt up
The layers
A paver patio is a stack. Compacted gravel base at the bottom, a 1-inch layer of bedding sand on top, the pavers, then joint sand swept into the cracks. ICPI gives 1 to 1.5 inches for the bedding sand. We start at 1 inch, and you can change it.
Add the layers and you get the dig depth: gravel base + 1 inch of sand + paver thickness. With a 4-inch base and 2⅜-inch pavers, you dig about 7⅜ inches below where you want the finished surface.
How much gravel base
Drainage decides this. Sandy or gravelly ground that drains fast holds a patio on a thinner base; heavy clay and wet spots need more. We default to 4 inches for well-drained ground. Rogue Engineer defaults to 6. If water sits on your lawn after rain, or you dig into sticky clay, use 6 or ask your paver supplier what they recommend for your soil.
Compact the base in thin layers with a plate compactor, not all at once. A thick layer packs on top and stays loose underneath, and that's where dips come from two winters later.
The calculator sizes the base to your patio. If you want gravel running a few inches past the edge so the edging sits on solid ground, run it a second time with those inches added to the length and width, and use only the gravel line from that run.
Pavers and waste
Patio area divided by the face area of one paver gives the count. Then add waste for cuts and breakage. We use 5% for a straight edge and 10% for a curved one, the same figures Rogue Engineer uses. Curves mean cutting nearly every edge piece, and each cut leaves an offcut you can't reuse.
Buy from one batch if you can. Colors shift between runs, and a few odd pavers stand out more than you'd think.
Polymeric sand: read the bag
Coverage per bag varies a lot. Inch Calculator works with 25 to 50 square feet per bag; Rogue Engineer uses 80 to 100. The difference is joint width and paver thickness, and the brand. Wide joints and thick pavers swallow far more sand.
So the coverage field starts empty. Type the number from the bag you're buying, and the calculator counts bags from that.
Edging
Edging holds the outside row in place. Without it the edges creep outward and the sand washes out. The calculator measures the patio perimeter in feet. If a long side butts up against the house, tick the house box and that side comes off. For a short side, or more than one side against walls, subtract them by hand.
Slope
Water has to go somewhere, and it shouldn't be your foundation. Slope the patio away from the house. Rogue Engineer uses 1/8 inch per foot. Check what your paver maker recommends, since some ask for more. Build the slope into the gravel base, not the sand, so the sand stays an even inch.
Questions people ask
How many pavers do I need for a 10×10 patio?
100 square feet divided by the face area of one paver, plus 5% for a straight edge or 10% for a curved one. Enter your paver's length and width above for an exact count.
How much sand do I need for pavers?
Two kinds. Bedding sand goes under the pavers, 1 inch deep, and the calculator gives it in cubic yards. Polymeric sand fills the joints; count it by the coverage on the bag. That's the sand paver calculator part of the list.
How deep should the gravel base be?
We default to 4 inches for well-drained ground. Use more for clay or wet spots; Rogue Engineer uses 6 inches as its default. Your paver supplier knows local soil best.
Why is the polymeric sand field empty?
Because coverage ranges from about 25 to 100 square feet per bag depending on the brand, joint width and paver thickness. A built-in number would be wrong for many patios. Type the coverage from your bag.
Does it work as a brick paver calculator?
Yes. Enter the brick's length, width and thickness in inches. Any rectangular paver works the same way.
How deep do I dig for a paver patio?
Base depth plus 1 inch of bedding sand plus the paver thickness. The calculator shows this number with the shopping list.
Does it estimate cost?
No. Prices depend on your region and supplier, and we'd only be guessing. Download the CSV and add your local prices next to each line.